- Wrench has 1/2" Anvil with pin retention for easy socket connection
- The Powerful 18-Volt motor allows 0-3000 RPM to tighten or loosen
- 200 ft. lbs. [2400 in lbs]
- Bright LED Light
This is an inexpensive electric cordless impact wrench and not really meant for the tough jobs. If you expect to regularly and quickly remove lug nuts and rusted bolts, this is not the impact wrench to use. For those jobs, I have an Ingersol Rand 600 ft.lbs. air impact wrench.
If you are working on ATVs, Snowmobiles, Lawn and Garden equipment then this is a great tool to have around. It works well and quickly for those applications.
But if you are considering buying this on its own, it will cost you at least another $100 for a charger and batteries. And I don't think it is a good value then. Or if you are thinking of buying this to replace an air impact wrench then you will probably be disappointed.I'm already locked into one+ hardware with two drills and on my third set of two NiMH batteries. Drills have held up for 5+ years and the batteries have died predictably and consistently. I had my choice between the 1/4 in hex drive only model, or this 1/2" Impact wrench model.
My first test was to remove and retorque bolts holding bike axles on children's bikes. I used my standard one+ batteries and found I could kill a partially charged battery within four bolt-removal and torque attempts. A full charge on a standard one+ NiMH probably yields 8-10 applications of 100+ft/lb bolts.
I will definitely need LiIon batteries and charger to get more work out of a charge cycle however the investment in batteries and charger take the expense of ownership into dewalt and makita territory where I'm probably headed.
It is noisy however I'm happy to not be dragging a noisy compressor and 50 feet of hose along.
The pricing of this driver unit as a bare tool placed it in with 1/4 Hex drive units however the torque reserve is far greater than any of those units.
Unexpected benefits:
Where I would have used a stepped bit on my 18V drill before and struggled with binding, this thing will tear through any drilling task I've tried with a stepped bit. Using a little finessing with the speed I can apply lower torque and the driver works effortlessly. From that standpoint driving a 3.5 in deck screw into harder wood is like driving a screw into balsawood.
The NiMH batteries may bring more endurance to the tool however I've only used it for a series of small jobs.
If you're buying a set of tools, not tied to the one+ you have a lot of good choices. If you're stuck/committed to one+ tools and already use Li-Ion batteries it's a decent tool and will do what you need as long as you're not pushing it to 200ft/lb constantly. If you are you will be happier with Dewalt/Makita higher tier brands, air tools or electric(AC) powered tools.First thing I did to test this gun was remove lugs on my 4x4 truck . worked like a champ with a 3/4 charged old style nicad battery that is two years old. I put those lugs on myself with an air impact months ago.
second thing was four inch screws, no problems there. its loud but thats to be expected from an IMPACT wrench. very happy with this purchase.
I will mostly use this for construction work but its nice to know I can fix my vehicles with it too!
The chuck adapter is fantastic and if you pull the tip and insert the bits properly they cannot fall out. If this is unclear to anyone its all in the directions.Out of all the Ryobi tools I have, this one is the most sensitive about battery power. Feed this a fresh 3 amp hour NiMh (sold here at Amazon) or 3 ah lithium ion battery, it will handle just about any nut or bolt you point it at. Yet this tool struggles with tight nuts if battery is a little low on charge, or the battery is not 3 amp hour.
I did an engine, transmission, and harness swap between two cars. Project would not have been possible without this tool. I had to use a breaker bar with some head bolts. This tool can handle any head bolt after you crack it with a breaker bar.
Feed it a good battery, you will be pleased. I have owned this tool 9 months. Not as strong as a name brand pneumatic wrench, but good deal for the price. Certainly more powerful than other electric impact wrenches I have tried.
I give this 3 stars for two main reasons:
1. This drill is extremely loud, not a deep rumble of a V8 type of loud, but a high pitched crackling, blood curdling shrill that you think the drill is about to explode in your hands type of loud. I bought this drill for autocrosses/drag racing when I change my wheels at the track and want to be lazy and not have to use a breaker bar to loosen lugs before jacking up the car. This drill is so loud when breaking lugs that strangers will come over and ask if everything is okay and your ears will slightly ring. I have used impact air tools in my garage all day long with no issues, but this electric-motor monster has the most unpleasant shrill. I don't have a decibel meter, but this is probably 10x louder than any cordless impact I've ever used.
2. You need to realize what you're getting into when you get this drill. These Ryobi drills do not come with batteries and furthermore do not come with a way to charge the batteries. You can visit your local Home Depot and it is the same story. A drill is no good without a battery and a battery is no good without a charge. So now you have to pay $35-$45 for a charger and $89-$100 for a battery! Keep that in mind before jumping into this. If you already have some existing Ryobi tools that use the One+ lithium ion battery system, then the cost isn't so bad, but it kinda locks you into using Ryobi. If this will be you first and only Ryobi, then you're paying a lot for a cordless impact wrench and might want to consider a DeWalt.
As far as longevity, that is unknown for now, I just know it makes quite the racket in doing so. I've used other cordless impact wrenches and they have a "wind-up" type of impact, this Ryobi just makes significant noise from the get go, I almost prefer the quieter, yet slower to do the same job, "wind-up" type of cordless impact wrenches.
The lug nuts on my race car are always torqued to 100 ft/lbs as specified, it may take 4-5 seconds of "impacting" to loosen 1 lug, even though the Ryobi P260 is rated at 200 ft/lbs now it has always done the job, but multiply that by 5 lugs x 4 wheels and that's a lot of noise. I know I keep hounding on the noise, but once you use it, you'll know what I mean.
0 comments:
Post a Comment